Atima Pressure Washer Pump 2.5 GPM 2900 PSI Horizontal 3/4" Shaft fit 6.5 HP Eng

Description

Atima Pressure Washer Pump 2.5 GPM 2900 PSI Horizontal 3/4" Shaft fit 6.5 HP Engine Brass Head Replacement Pump
Product Description
This pump produces between 2 PSI 2.5 GPM 3/4" Horizontal Shaft pressure washer pumps
Homelite 03 57 07 UT80522 UT80953 UT80522B UT80953B UT80522A UT80953A UT80522D UT80522E HL252300
Powerstroke0, PS80522, PS80903A, PS80903B
Delta DXPW3025 G2400HH
Karcher K2400HH MH5500H-1 M5500H-2 M5500H-3
KarcherG3050OH
Generac 07, HL252300, 01675, 01675-0, 1675, 1675-0, G24H
Craftsman 00 01
Generac AXD2524GT-22MM AXD3025G
Simpson MSH3125, MSH3125-S
Annovi Reverberri SJV25G27D-F7-EZ
AR MV25G30D - OEM
RMV25G30D-PKG RMV25G30-EZ-PKG
Technologies FNA520002 (SIMPSON 520002)
Engines: OEM Himore 03 Engines, Honda GC160, Honda GC190
Why ATIMA is your better choice?
ATIMA is a leading designer and manufacture of portable inverter generators. ATIMA generators give you the power that you need. Whether recreational or professional ,ATIMA will be there.
PUMP INSTALLATION
1:Install the shaft key into the keyway and apply a light coating of anti-seize on the engine shaft and key
2:Align the two key ways and push the pump completely onto the engine
3:Install all four (4) bolts and tighten evenly
4:Install the appropriate water inlet and discharge fitting
5:Connect the water supply hose and high-pressure discharge hose/spray gun.
6:Turn on the water supply
7:Open the spray gun to purge the system of any air
8:Start the engine
If necessary adjust the engine speed and unloader valve
Do not exceed the pump specifications in speed or pressure.
Read more
Easy Connection
This plunger pump will pump up to 2.5 GPM at 2900 PSI. It
spins at 3450 RPM in a direct drive system coupled with a gasoline engine.
The matching flange provides convenient connection to most 3/4”shaft 6.5
HP or more high engines.
Easy injection
The hollow shafted pump includes a built-in
pressure control valve, and chemical injection system.
Protection
We designed the protection mechanism here, it can protect pump from overload.
but if you can not sure, you can see the manual.
Read more
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE AND SOLUTION Oil leak from crankcase Worn rod oil seals.(Replace crankcase piston rod seals) Pump runs but produces no flow Pump is not primed(Flood suction then restart pump) Pump fails to prime Air is trapped inside pump(Disconnect discharge hose from pump. Flood suction hose, restart pump and run pump until all air has been evacuated) Low pressure Worn nozzle.(Replace with nozzle of proper size.) Low pressure Belt slippage(Tighten or replace with correct belt.) Low pressure Air leak in inlet plumbing.(Disassemble, reseal and reassemble.) Low pressure Relief valve stuck, partially plugged or improperly adjusted valve seat worn.(Clean and adjust relief valve; check for worn or dirty valve seats.)
Durability&Longevity: Horizontal pressure washer Pump with Brass Head!!! It must be very satisfied and impressed!!! These high pressure pumps really need a quality oil for longevity Don't worry. We already add 120ml oil inside the pump, the oil can protect the pump safety. You don't need to add oil during normal use.
High Pressure: 2900 PSI / 2.4 GPM - MAX 2.5 GPM. This pumps is rated at 2900 PSI and 2.3 GPM which is great for any and all small house cleaning.
Easy to Install:Simple to start, easy to install, clean dust in one step.
Fit Most 3/4" Shaft Engines: Distance to the hole is 2 5/8", Outer Holes is 1 7/8", 2 5/8". Only fit 3/4" shaft Horizontal pressure washers.
Engines Brand: Power Pressure Washer Pump Fits Honda(only 3/4" shaft), Generac, Briggs & Stratton, Craftsman, Karcher, Blackmax, Ryobi, Troy Bilt, Craftsman, Simpson, Powerstroke.