Blower Car Wash drying system 2 10 HP high efficiency watch on youtube

Description

New Car Washing Drying System, 3600RPM motors New 3 phase Electric. Motor is UL approved Runs quietly
We shipped one of these to
Ohio
from
New York
for 0.00 shipping cost fully insured
We shipped
2
of these to
California
from
New York
for 7.00 shipping cost fully insured
Saves labor and time when washing cars even hand washing.
Saves towels... Big labor savings
Ask for pricing on optic sensors and stands...   optic sensors and stands are 0 with time delay
Ask about motor starter kit available with 3 wire protection  Please provide voltage for price .   440/460 volts AC motor star ticket Triple wire protection  with three wire, 3 poll circuit breaker assembled in steel cabinet box all UL approve components 0. Please check your voltage prices vary
One left side One right side ........................................... Topside down blower also 10 horsepower would add to the cost 00.
2 blower producers on a steel  stand. framed stand is white industrial Coating    3 X 3 Heavy duty angle
Vibration reducing feet pads,  wage anchors for mounting to concrete included
10 horsepower blowers are three phase electric  208/230/460 volt AC
All motors work and test  fine
Almost forgot to put in the youtube video link
http://youtu.be/0lZk-gJsfnU
100%
http://www.spinnercarwash.com/AirDryingSystems.html
Allow  10 days Before  shipping  After closing of the auction allowed 10 days before the equipment is shipped .
If you have a processor or programmable controller
in your CarWash equipment there possibly is a start output marked either Air Dryer or Blower.
Some places we start the Air Dryer with the final rinse of the CarWash itself.
If The Blower starts
when the Final Rinse Arch starts it gives the motors ample time to get up to speed to produce the right amount of air flow to remove the water from the vehicles as they pass under.
Motor starters are required with overload thermal protection and a shut off and depending on the voltage they can run anywhere from 0 to 0 for each motor.
If you have no processor for your Car Wash Equipment you can use a tape switch that will also require a timer.
If the tapes which is not feasible you can use an infrared optic switch to detect the vehicles entry into the Blower area.
A time delay on shut off should be included and the optics sensor beam should be installed several feet ahead of the blower nozzles to allow motors to come up to full speed
Time delay relay should be (OFF delay timer with momentary start input) anything 3 to 5 minutes.
This time delay will allow you to adjust for speed of the car going through to complete and turn off by the back of the car also allow if you have a second following car that the Blower does not turn off and then turn on again.
Keeping the motor running for following cars will save you both wear and tear on the equipment and cost of electricity.
In one hand wash CarWash application we used a wireless remote control after the car was soaked down with soap and water washed by hand mitts the driver would activate a final rinse and air drying unit with a remote control button he carried in his pocket.
One click and the Blower and Final Rinse would stay on for 3 to 5 minutes.
2 -
7 1/2 horsepower
motor control package including, time delay, 2 - motor starters and 2 - thermal overloads with 2 - disconnects assembled and wired with a wall mounted enclosure.
All you need to do is connect your three phase power leads from your power source disconnect, wire the motors to the box, connect your input leads from your processor.
5.00
Infrared sensing kit with Floor Mounted Stainless Steel stands, power strip, waterproof wiring harnesses and concrete anchors.
We'll be an additional
,275.00
Wireless remote control with four channels programable to (on - off)
(momentary on) (momentary off) (auxiliary on - off) includes two remotes.
Works within approximately 90 feet
We'll be an additional
0.00
As far as drying the top of the 7 1/2 horsepower units with (5)five socks, the highest nozzle is 85 inches from the ground that will do very well with all sizes standard cars and pretty good with minivans and large SUV's large full size vans it will move the water off the windshield pretty well along with the bottom part of the van, however the top roofs of full size vans will not be reached as well.
The 10 horsepower unit with (6) six socks
the highest nozzle is 96 inches above the ground it will push water all off the top of full size vans as well as the smallest cars.
The pivot and cross action of both these is designed removal of water from the grill in headlights, hood and
fenders - including wheels windshield and side windows, roofs of cars, rear windows and trunk lids
I hope that answered all your questions